Equipment We Service
Concrete Grinder
- Change engine oil/filter, replace air filter, and verify start/run, idle, and throttle response.
- Replace spark plugs; set belt tension to factory spec; inspect propane/fuel/vacuum hoses and fittings; replace as needed.
- Diagnose vibration/noise and driveline wear; service hub bearings and related components for smooth operation.
- Replace worn parts as required (belt, carburetor, hoses, hub bearing) and complete a final safety/function test.
Auto Scrubber
- Clean recovery tank and float sensor; inspect/adjust squeegee and scrub brushes; verify proper suction and scrub performance.
- Clean battery terminals/cables; check battery state of charge and replace if needed.
- Check trans-axle fluid level and top off; grease rear casters and inspect drive components.
- Replace wear items as needed: head brushes, squeegee blades, skirt around the heads; check carbon brushes in electric motors.
Vacuum
- Clean HEPA and sock filters; check airflow/suction and overall operation.
- Inspect electrical connections; clean inside the electrical panel; inspect power cord and strain relief for damage.
- Replace HEPA and sock filters as needed; check motor amperage draw and confirm parameter/settings are correct.
- Inspect/replace casters and hardware; final function test to verify stable performance on-site.
Burnisher
- Change engine oil and filter, replace air filter, and perform an operational inspection (start/run, idle, throttle response).
- Replace spark plugs, set belt tension to factory spec, and inspect all fuel/vacuum/propane hoses and fittings; replace as needed.
- Diagnose vibration/noise and driveline wear; service hub bearings and related components to restore smooth burnishing.
- When required, replace key components (belt, carburetor, hoses, hub bearing) and verify safe, consistent performance.
Polyurea Pump
- Flush the system with approved cleaner to break down hardened material in pumps, lines, and the manifold.
- Inspect/clean pump section, filters, and valves; confirm proper flow, pressure, and balanced output.
- Adjust chain/belt to factory spec; grease manifold and moving components; verify smooth operation.
- Inspect electrical connections and hydraulic lines for wear/leaks; replace with stainless-steel braided lines/manifold components as needed.
Twister/Hurricane
- Hydraulics: troubleshoot slow lift/drive, pressure loss and leaks; service pumps, hoses, fittings, cylinders, valves.
- Drive/steering: fix tracking/pull and jerky movement; service drive motors, hubs, chains, linkages; verify smooth response.
- Cutting head: replace blades, blade holders, drums/hardware; set depth/angle for better removal rate and finish.
- PM & safety: fluids/filters, grease points, fastener torque, electrical/switch checks; job-ready inspection.
Shot Blaster
- Blast system: inspect/replace wheel, blades, liners, control cage, seals; restore profile & production.
- Drive & bearings: diagnose vibration/noise, replace bearings/shafts, service belts/chains, set alignment/tension.
- Dust & airflow: fix suction loss, leaks, hoses, filters; protect internals and keep jobsite clean.
- Electrical/safety: test switches, contactors, wiring, E-stop; verify smooth start/stop and safe operation.
Demolition Tools
- Power loss/leaks: rebuild impact section (piston/striker, seals, o-rings); correct lubrication.
- Chuck & retainer: replace bushings, springs, retainers; reduce bit slop and premature bit wear.
- Motor/gearbox: diagnose overheating/low RPM, replace bearings/gears, tune brush/trigger components where applicable.
- Electrical: repair cords, switches, wiring, and battery/charger connections; test under load before return.
Concrete Saws
- Inspect/repair engine or motor drive system; tune belts/pulleys, throttle, and start/run performance.
- Service blade shaft, arbor, bearings, and guards; correct vibration, runout, and uneven cutting.
- Check depth-control and tracking components; adjust wheels, linkages, and alignment for straight joints.
- Replace worn blades/arbors/hardware; service fluids/filters and perform a full safety/function check.
Some of the brands we service include:
SASE, HTC, Husqvarna, Scanmaskin, Innovatech, Pullman Ermator, Werkmaster, Blastrac, Edco, Velo Bond, Hi-Tech Polyurea Pumps, U.S. Saws, Metabo, Diamatic, and many more!